Language
KSB Belgium sa/nv
 |
Stand F4002 Contact details
1301 Wavre |
Loading... |
Products
|
PumpMeterThe PumpMeter device is an intelligent pressure transmitter for pumps, with on-site display of measured values and operating data. The device consists of two pressure sensors and a display unit. It records the load profile of the pump in order to indicate any potential for optimising energy efficiency and availability. |
|
MegaCPKDesign |
|
Etanorm (PumpDrive & PumpMeter)Horizontal, long-coupled, single-stage volute casing pump with ratings and main dimensions to EN 733 in back pull-out design, with replaceable shaft sleeves / shaft protecting sleeves and casing wear rings. Design to ATEX. |
|
PumpDriveDesign |
|
Etaline (PumpDrive & PumpMeter)Close-coupled, in-line circulator pump with volute casing and standardized motor. |
|
Etabloc (PumpDrive & PumpMeter)Close-coupled, single-stage volute casing pump, ratings to EN 733, with replaceable shaft sleeve and casing wear rings. Design to ATEX. |
|
Boax-BCentered disc butterfly valve with elastomer liner (EPDM XC or Nitrile K). With lever, manual gearbox, electric or pneumatic actuator. Wafer-type body (T1), semi-lug type body (T2), full-lug type body (T4), U-section body with flat faces (T5). body types T2, T4 and T5 are suitable for downstream dismantling and deadend service. Valve disc made of nodular cast iron or stainless steel. EN, ASME, JIS connections possible. |
|
Boax-SButterfly valve for building services, with anti-condensation feature, elastomer liner (EPDM XU or Nitrile K). With lever, manual gearbox or pneumatic actuator. Semi-lug type body (T2), suitable for downstream dismantling and dead-end service. Valve disc made of stainless steel 1.4308. Connections to EN possible. |
|
Boax-SFDesign |
|
Sisto-16 TWAFlanged diaphragm valve for drinking water installations to DIN 1988, DIN-DVGW Water approved acc. to test W 270, in compliance with KTW recommendations (use of elastomers in drinking water applications); shut-off and sealing to atmosphere by completely enclosed diaphragm; position indicator with integrated stem protection. All moving parts are separated from the fluid by the diaphragm. Maintenance-free, PN 16. |
|
Sisto-16 RGADiaphragm valve with gunmetal body and threaded ends for drinking water installations in building services to DIN 1988, DIN-DVGW Water approved acc. to test W 270, in compliance with KTW recommendations (use of elastomers in drinking water applications); shut-off and sealing to atmosphere by completely enclosed diaphragm; position indicator with integrated stem protection. All moving parts are separated from the fluid by the diaphragm. Maintenance-free, PN 16. |
|
Boa-CompactFlanged end globe valve with short face-to-face length to EN 558/14, slanted seat, bonnetless, EPDM coated throttling valve plug, soft main and back seat, position indicator, locking device, travel stop, insulating cap with anti-condensation feature; maintenance-free, asbestos-free, full insulation possible. |
|
Boa-SuperCompactWafer-type globe valve in super compact DN face-to-face length, slanted seat, bonnetless, with flange alignment holes for centering, dead-end service and downstream dismantling, insulating cap with anti-condensation feature as standard, position indicator, soft main and back seat; maintenance-free, asbestos-free, full insulation possible. |
|
Boa-Control IMSBalancing valve with electronic sensor for flow and fluid temperature measurement with BOATRONIC M-2 measuring computer for hydraulic balancing with short-term measurement, with BOATRONIC M-420 for analog signal transfer, e.g. to a control room. Independent of minimum differential pressures; constant accuracy across the entire range of valve travel. Standard: locking device and travel stop. Maintenance-free, asbestos-free, full insulation possible. |
Press releases
-
New standardised chemical pump for the global market
The KSB Group, Frankenthal, Germany, will debut the latest generation of its standardised chemical pumps. The new MegaCPK type series distinguishes itself above all by a high output per size and hence very low energy consumption. It is an advanced version of the internationally successful CPK, CPKN and Megachem type series.
At identical operating data and conditions the user can select smaller pump sizes compared with previous generations and competitor products. This will not only save energy during operation but will also reduce initial investment costs. In order to minimise the risk of cavitation, KSB’s development engineers put special emphasis on good suction behaviour at a low NPSH value. This is why even under tough operating conditions the pumps will run quietly and smoothly. Their reliability is thus ensured and the availability of the entire system is increased.
With the help of the finite element analysis (FEA), a calculation method for structural simulation, it was possible to increase the pump sets’ rigidity. Another benefit in this respect is the optimised single-piece bearing bracket. The easy-to-service mechanical seals, fully confined casing gaskets and minimal axial thrust ensure long pump service lives and reduced life cycle costs since the owners/operators spend less on maintenance and repair.
As is common practice with all industrial pumps by KSB, the pumps delivered to the owner/operator are provided with impellers whose diameters are matched precisely to the operating point. In addition to the large variety of pump sizes on offer, this is the only way to ensure that the pumps require as little energy as possible.
For special applications, a range of models and material variants are available, allowing to also transfer fluids that require heating or cooling. Manufactured at production sites in Europe, Asia and South America, the new type series is integrated in a production and service network which means a high level of availability for owners/operators.
-
KSB is a winner in the “British Pump Industry Awards”
KSB is a winner in the “British Pump Industry Awards”
On Wednesday, 23 March 2011, KSB Limited (UK) was given the coveted award for “Environmental Contribution of the Year”. At this year’s “Pump Industry Awards” in Coventry, KSB Limited received the award from the British Pump Manufacturers’ Association (BPMA) for and on behalf of the KSB Group.
KSB Limited, represented by Peter Maslin, General Manager – Sales & Contracts, was presented the award by Selina Scott, the well-known BBC newsreader, and Gustavo Iensen, Regional Director for Europe of WEG Electric Motors. It was the pump monitoring unit PumpMeter and the variable speed system PumpDrive that achieved recognition. Attending the ceremony were about 250 representatives from major manufacturers, operators and key accounts from various industries. Started in 1997, the “British Pump Industry Awards” are firmly established as a special event on the calendar in Great Britain. Through the award, the BPMA intends to promote and honour outstanding achievements in pump technology. In addition to picking up the award for “Environmental Contribution of the Year”, PumpMeter was also a finalist in the category for “Technical Innovation of the Year”. The monitoring unit continuously analyses the pump’s operating data and establishes its energy saving potential. The PumpDrive variable speed system matches pump output to actual demand and allows energy savings of up to 60 percent. As a member of Europump, the BPMA has represented the interests of UK suppliers of pumps and pumping equipment for over 50 years.
Product news
-
PumpMeter
The PumpMeter device is an intelligent pressure transmitter for pumps, with on-site display of measured values and operating data. The device consists of two pressure sensors and a display unit. It records the load profile of the pump in order to indicate any potential for optimising energy efficiency and availability.
Applications: For monitoring the operation of a centrifugal pump. -
MegaCPK - A new era starts here
With the new MegaCPK, KSB has developed a novel and global generation of products. The standardised chemical pump combines high energy efficiency, maximum versatility and outstanding operating reliability for plenty of applications.
Content is provided by exhibitors. If you consider any content inappropriate or misleading, please contact info@easyfairs.com
                    |
Media & Partners
Search products
Related show(s)
- PUMPS & VALVES 2013Netherlands, Rotterdam02/10 - 03/10/2013